Huawei OptiX OSN 1800 OTN/WDM Transport Family | I X, II and V Pro

Huawei OptiX OSN 1800 OTN/WDM Transport Family | I X, II and V Pro

Huawei OptiX OSN 1800 Family Overview

The Huawei OptiX OSN 1800 is a multiservice optical transport family for metro and access networks. It combines OTN, WDM, packet transport and, on supported configurations, SDH to carry broadband, private-line, mobile, enterprise and data-center traffic over a unified platform.

Huawei documentation has evolved across product generations. The current portfolio can be presented in three main groups: OSN 1800 I X, the OSN 1800 II family (II Pro and II TP), and OSN 1800 V Pro. The two II variants are described separately because their slot counts and published switching specifications are not interchangeable.

1. OSN 1800 I X: Compact Access Platform

OSN 1800 I X targets compact metro-edge and access locations, enterprise sites and nodes requiring multiservice optical transport in a small footprint. Recent portfolio material describes a 1U design with two 100G line ports, service access from low-rate telecom interfaces up to 100G, and network scalability depending on the deployed configuration.

Hardware and board groups

  • Client-service and tributary boards for Ethernet and OTN service access.
  • Line/transponder boards that map client signals to optical line wavelengths.
  • Optical mux/demux and wavelength-management boards for CWDM/DWDM configurations where supported.
  • System control and communications, power and fan units; redundancy depends on the exact chassis version.

Capacity note: Older OSN 1800 I Enhanced documentation lists 40G OTN switching, 120G packet capacity and TDM switching of 42.5G high-order / 5G low-order. These figures must not be assumed for the newer I X without its matching hardware and software release documentation.

2. OSN 1800 II Family: II Pro and II TP

The II family is positioned between the compact access platform and the larger V Pro aggregation chassis.

OSN 1800 II Pro

  • 2U chassis.
  • The OSN 1800 Portfolio brochure specifies 6 service-board slots for the DC chassis and 4 for the AC chassis.
  • Published switching capacity: up to 800G OTN and 800G packet, with 60G high-order and 10G low-order TDM.
  • Supports 1- to 9-degree ROADM in the corresponding optical configuration.
  • Published line rates include 2.5G, 10G, 25G, 100G and 200G.

OSN 1800 II TP

II TP is also a 2U platform, but its slot configuration and capacity must be treated separately from II Pro. The portfolio brochure specifies 2 service-board slots for DC and 1 for AC, with 1- to 9-degree ROADM capability in the applicable optical configuration. The same brochure does not publish a switching-capacity figure for II TP; the II Pro 800G figure must not be assigned to it.

Important board families

  • Optical transponder and wavelength-conversion boards for client-to-line adaptation.
  • 100G service-convergence boards; TMB1LDCD and TMB1LDC appear in hardware documentation for II Pro/TP and V Pro generations.
  • Multirate wavelength-conversion boards such as TMB1LDCA and TMB1LTX.
  • Multirate optical boards such as TNF2ELOM and TNF2LDX in the documented hardware generations.
  • Control, cross-connect, clock and communications boards. The documented II Pro configuration identifies TMK2UXCLE, while II TP is shown with TMT1SCC.
  • Power and fan boards selected according to AC/DC chassis and redundancy design.

3. OSN 1800 V Pro: Higher-Capacity Aggregation Chassis

OSN 1800 V Pro is intended for higher-capacity metro aggregation nodes carrying larger numbers of services and optical channels.

  • Approximately 221.5 mm chassis height.
  • 14 service-board slots for DC and 12 for AC, according to the OSN 1800 Portfolio brochure.
  • Published switching capacity: 920G OTN and 920G packet, with 160G high-order and 20G low-order TDM.
  • Supports 1- to 9-degree ROADM in the applicable optical configuration.
  • Published line rates include 2.5G, 10G, 25G, 100G and 200G.
  • The evaluated hardware configuration identifies the system control/cross-connect board as TMK5UXCME.

 

 

Key board groups

  • Optical transponder and wavelength-conversion boards for DWDM line interfaces.
  • 100G/OTU4 service-convergence boards; TMB1LDCD and TMB1LDC are documented board families.
  • Multirate boards such as TMB1LDCA and TMB1LTX.
  • Ethernet and packet-processing boards for GE/10GE/25GE and higher-rate services, subject to the board configuration.
  • OTN tributary and cross-connect boards for ODUk mapping and switching.
  • ROADM, optical amplification, mux/demux and optical-monitoring boards as required by the line design.
  • System control/clock, power and fan boards for equipment control and redundancy.

4. Chassis and Capacity Comparison

Model Chassis height Service slots Published switching capacity
I X 1U Version-dependent Refer to the I X release-specific datasheet
II TP 2U 2 DC / 1 AC No separate switching figure in the Portfolio brochure
II Pro 2U 6 DC / 4 AC OTN 800G, Packet 800G, TDM 60G HO / 10G LO
V Pro Approx. 5U 14 DC / 12 AC OTN 920G, Packet 920G, TDM 160G HO / 20G LO

The family brochure specifies up to 80 DWDM wavelengths and 8 CWDM wavelengths. The supported rate per wavelength, including 100G or 200G, depends on the line board, optical module, software release and optical design.

5. Supported Services and Applications

  • Ethernet and enterprise private-line services.
  • OTN mapping and ODUk transport.
  • SDH/SONET and PDH transport on supported models and boards.
  • Mobile backhaul and radio-site aggregation.
  • Metro network and data-center interconnection.
  • CWDM/DWDM and ROADM on supported configurations.
  • Service protection and optical-layer monitoring according to the network design.

6. Engineering and Selection Notes

  1. Do not confuse chassis switching capacity with the line rate of an individual optical board or the sum of client ports.
  2. The 800G and 920G figures belong to II Pro and V Pro respectively in the cited portfolio brochure; they must not be applied to II TP or I X.
  3. A board name alone is not enough for procurement. Verify the full board code, hardware revision, chassis type, software release and slot restrictions.
  4. DWDM engineering requires wavelength planning, per-channel rate, optical power budget, amplifier design, distance, OSNR and fiber characteristics.
  5. ROADM degree and optical-layer features depend on the chassis, optical boards and line-system design.
  6. Always check the Hardware Description and Product Description for the exact release before ordering or expanding a live system.

Conclusion

Huawei OptiX OSN 1800 is a multiservice optical transport family that belongs in the POTN portfolio. I X addresses compact access nodes, II Pro/TP covers mid-sized aggregation with important differences between the variants, and V Pro targets higher-capacity metro aggregation. Final selection must be based on verified switching capacity, service slots, supported boards and the DWDM/ROADM line design.

Technical note: Board names and supported capacities vary by generation and software release. The board families above are traceable examples from hardware documentation, not a claim that every listed board is compatible with every OSN 1800 chassis.

Request a quote